PET bottled water equipment

Purified Water Filling Line

A purified water filling line connects a defined treated-water supply to PET bottle rinsing, filling, capping, labeling and packing. The filler is not a water purifier. Match usable treatment output, storage and production hours to the bottle schedule, then specify the equipment and interfaces needed to turn that water into accepted finished packs.

Water Treatment and Storage
Bottle Feeding and Air Conveyor
Rinsing, Filling and Capping
Buyer planning content Prepared by Mr Kcal Procurement scope reviewed by Allot Tech

Project fit

Who This Line Is Suitable For

Use these points to confirm whether this configuration matches your procurement scope.

  • Purified drinking-water projects sizing treatment and PET filling as one operating system.
  • Plants expanding bottle output while checking whether existing treatment and storage can support the change.
  • Buyers comparing treatment-plus-packaging proposals with separately sourced process and filling equipment.

Recommended Configuration

Treatment basis Feed-water analysis and finished-water specification; process, recovery and usable output confirmed by the treatment supplier.
Storage and transfer Itemize usable holding volume, transfer equipment, instruments and connections.
PET filling group Rinser, filler and capper selected for approved bottle/closure formats and product duty.
Downstream package Conveyors, labeler, coder and packer matched to sustained bottle and pack flow.
Site responsibility Identify incoming water, drains, power, air, cleaning services and local installation work.

Typical Technical Parameters

Product Still purified drinking water delivered to the filler at the agreed inlet conditions.
Filling output Good bottles by approved format and operating schedule, not one BPH for every bottle.
Water output Separate raw feed, treated product and filler consumption in liters per hour.
Package PET bottle, neck, cap, label and pack pattern approved through drawings and trials.
Cleaning and release Agreed method, component compatibility and responsible quality-release procedure.

Bottle Size Compatibility

Launch formats List each bottle volume, geometry, neck and cap rather than specifying only a minimum and maximum volume.
Production rate Request a separate rate for each format and include changeover in the shift schedule.
Packaging changes Check label materials, code positions and bottles per pack with the same approved formats.
Test materials Agree representative bottle, cap, label and packing samples before final acceptance.

Build the Purified Water Process and Packaging Boundary

Treat the following as interface decisions, not a universal treatment recipe. The treatment supplier needs source analysis and the finished-water requirement; the filling-line supplier needs the resulting water duty and bottle schedule. Use the treatment scope guide to record what remains unresolved.

Build the Purified Water Process and Packaging Boundary - Planning Table

Stage Planning input Required handover information
Feed water to treatment Source condition, available flow and intended product. Selected process, operating assumptions, usable output and waste streams.
Treatment to holding Production hours, cleaning schedule and operating interruptions. Tank boundary, usable volume, instruments and quality-control responsibilities.
Holding to filler Peak format-specific water draw and approved inlet condition. Pump and piping scope, controls, cleaning coverage and connection details.
Filled bottle to finished pack Label, code, pack count and removal method. Sustained pack rate, accumulation, replenishment and discharge arrangements.

Calculate Product Water, Raw Feed and Reject Water Separately

For illustration, 5,000 bottles per hour at 0.5 liters each requires 2,500 liters per hour of nominal filled product. If an RO stage supplies that product at an assumed 75% recovery, feed equals product divided by 0.75. The recovery is an example only; it must come from the actual treatment design.

Calculate Product Water, Raw Feed and Reject Water Separately - Planning Table

Quantity in the example Calculation Boundary
Nominal filled product 5,000 x 0.5 = 2,500 L/h Water going into bottles at the illustrative reference rate.
RO stage feed at 75% recovery 2,500 / 0.75 = 3,333.33 L/h Feed for this simplified RO balance only.
RO reject stream 3,333.33 - 2,500 = 833.33 L/h Separate from pretreatment backwash and other drains.
Other site water users Calculate from their own duty and schedule Rinsing, cleaning, backwash, losses and other consumers are additional.

A Storage Tank Can Bridge a Shortfall, Not Fix the Daily Balance

Suppose the filler draws 2,500 L/h while treatment supplies 2,000 L/h. The net draw from storage is 500 L/h, so a 30-minute run consumes 250 liters of usable reserve. This simplified arithmetic is not a tank-size recommendation: usable operating levels, cleaning, residence conditions and process controls require design review.

  • Check treatment production across its actual operating hours against total daily demand.
  • Show when the tank refills, not only how long it can support filling.
  • Account for startup, stops and each bottle format. A larger tank cannot resolve an enduring daily supply deficit.
  • Review the utility schedule and site layout before specifying storage.

Decide Whether Existing Treatment Can Be Retained

A nameplate flow is only a starting point. Obtain usable output under the relevant feed-water condition, operating records, cleaning downtime and the approved product requirement. Then check pumps, transfer piping, controls and sampling arrangements. Reusing a treatment skid does not automatically make the existing transfer system suitable for a faster filler.

  • Identify whether the stated treatment capacity is raw feed or finished-water output.
  • Check operating recovery and the destination of reject, backwash and cleaning streams.
  • Confirm who verifies the retained system and who completes any modifications.
  • Keep new treatment, retained treatment and unresolved items separate in the equipment scope register.

Commission the Water Supply and Packaging Line as Connected Systems

Plan the checks with the responsible process, equipment and site parties. A dry conveyor demonstration cannot establish water quality, and a treatment sample cannot establish finished-pack output. Define the evidence needed for each release.

Commission the Water Supply and Packaging Line as Connected Systems - Planning Table

Check Agree before testing Record at handover
Water supply Approved inlet condition, required flow and operating schedule. Actual observed supply and any deviations assigned for closure.
Cleaning and product release Covered equipment, cleaning method, sampling and responsible release party. Completed procedure and required quality records, not a generic hygiene promise.
Bottle and closure Approved materials, quantity/level checks and closure acceptance. Results tied to the tested format and machine settings.
Finished packs Counting point, run duration, rejects, stops and replenishment. Good output, interruptions and package inspection for the agreed test.

Get a Purified Water Line Quote on a Common Basis

Send the source information available, intended product, bottle and cap, required output by format, treatment already installed, label, pack, workshop and country. Request both process and packaging exclusions. Ask Allot Tech for a project-specific configuration, then compare the line cost factors. For a different water-product objective, use the mineral-water planning page rather than assuming an identical treatment scope.

Further Reading on Process and Utility Integration

Buyer questions

Questions Buyers Ask Before Quotation

Does a purified water filling machine purify the water?

No. The filling machine receives water meeting an agreed inlet requirement and packages it. Water treatment, holding and hygienic transfer must be specified separately, even when the same supplier quotes them as part of a complete project.

Is 2500 liters per hour enough for a 5000BPH 500ml line?

It matches only the nominal 2,500 L/h placed into bottles at that rate. Rinsing, cleaning, treatment losses and other consumers are additional. Check usable treatment output and the operating schedule rather than treating the bottle calculation as total plant demand.

How does RO recovery affect raw-water demand?

For the defined RO stage, raw feed equals product output divided by recovery as a fraction. At an illustrative 75% recovery, 2,500 L/h product requires about 3,333.33 L/h feed and produces about 833.33 L/h reject. Actual recovery and other water users require the project design.

Can storage compensate for treatment output below filler demand?

It can bridge a limited mismatch if sufficient usable reserve and appropriate operating conditions exist. At 2,500 L/h filler draw and 2,000 L/h treatment supply, a 30-minute period uses 250 liters of reserve. Storage does not solve a persistent daily water deficit.

Can I reuse my existing RO plant for a new PET filling line?

Possibly. Review feed conditions, product quality, usable output, recovery, operating downtime, storage, transfer and controls. Confirm modifications and responsibility for testing before assuming the existing plant can supply the new bottle schedule.

What changes when a purified water line switches bottle size?

Bottle handling, closure, label and pack setup may change, and the achievable BPH may differ. Recalculate liters per hour using the rate for that format and include changeover in the production schedule.

Balance Purified Water Supply With Your Bottle Schedule

Send your bottle size, target capacity and country, plus available treatment output and operating hours. Request a proposal that identifies water-supply assumptions and the complete packaging scope.

Request Quote
WA: +86 186 6213 1120 Quote