PET bottled water equipment

Mineral Water Filling Line

A mineral water filling line packages the specified water into PET bottles through rinsing, filling, capping and downstream packaging. It does not establish the mineral composition or approve the product description. Start with source-water evidence and the intended finished-water specification, then select the still-water equipment, bottle formats and operating capacity.

Water Treatment and Storage
Bottle Feeding and Air Conveyor
Rinsing, Filling and Capping
Buyer planning content Prepared by Mr Kcal Procurement scope reviewed by Allot Tech

Project fit

Who This Line Is Suitable For

Use these points to confirm whether this configuration matches your procurement scope.

  • Still mineral-water projects with a defined source and a finished-water requirement to preserve through filling.
  • Existing plants adding PET formats or replacing filling equipment while retaining an assessed water-supply system.
  • Buyers who need clear responsibility for source treatment, hygienic transfer, packaging and product release.

Recommended Configuration

Water preparation Process selected after source analysis and intended product review; no standard RO package assumed.
Filling scope PET bottle rinsing, still-water filling and closure application matched to the approved package.
Water interface Agree receiving point, inlet conditions, storage, transfer piping and cleaning responsibility.
Packaging scope Bottle feed, label, code, finished pack and discharge selected for the launch formats.
Quotation boundary Mark water process, filler, laboratory work, site services and local approvals separately.

Typical Technical Parameters

Water duty Still mineral-water project only; sparkling duty requires a separate process and equipment review.
Bottle formats Review each PET bottle and cap drawing; request format-specific output and change parts.
Capacity basis Required good bottles by format and shift, plus the available source and treatment supply.
Contact materials Confirm product-contact materials, seals and compatibility with the approved cleaning method.
Quality boundary Mechanical acceptance and finished-water quality release are separate documented checks.

Bottle Size Compatibility

Volume and shape Submit the launch volumes, height, body dimensions and shape. A volume range is not compatibility approval.
Neck and closure Provide neck finish and closure drawings, including the sealing surface and tamper feature.
Label and pack Specify label method, code position, bottles per pack and finished-package handling.
Format evidence Agree tooling, settings, test samples and the rate for each approved bottle-label-pack combination.

Define the Water Product Before Selecting Treatment Equipment

Do not use mineral water, purified water and water with added minerals as interchangeable equipment specifications. Their process objectives may differ. Have the responsible local product specialist confirm the intended designation and permitted process before purchasing treatment. This page is a machinery planning guide, not product approval.

Define the Water Product Before Selecting Treatment Equipment - Planning Table

Project question Input to obtain Effect on the filling-line brief
What water is entering the plant? Current source analysis, available supply and known variability. Defines the upstream information needed before specifying the filler inlet.
What finished product is intended? Written product requirements and destination-market review. Prevents a generic treatment package from being substituted without process approval.
Is composition meant to be preserved or adjusted? Approved process objectives and responsibility for any treatment or dosing. Keeps mineral composition decisions outside the mechanical filler specification.
Is the product still or sparkling? Product condition at filling, including any carbonation requirement. Avoids applying a still-water proposal to a different filling duty.

Connect the Water Source to the Filler With Named Responsibilities

The handover point must be a defined connection and operating condition, not simply the phrase water treatment included. Show the route from the confirmed process outlet to the filling machine on a flow diagram. Develop the upstream scope with the water-treatment planning guide.

Connect the Water Source to the Filler With Named Responsibilities - Planning Table

Interface Define in the proposal Record to request
Process outlet Required flow and water condition; party releasing water for filling. Approved process basis and inlet requirement schedule.
Holding and transfer Included tanks, pumps, piping, instruments and connection limits. Equipment list and connection drawing with retained items identified.
Cleaning coverage Which product-contact paths are covered and which require separate procedures? Cleaning scope, component compatibility and commissioning checks.
Sampling and release Sampling locations, responsible party and product-release procedure. Agreed quality plan; do not substitute a visual machine trial for water testing.

Select PET Rinsing, Filling and Capping Around the Actual Package

Review the bottle source, empty-bottle handling, rinsing medium, fill method and closure application together. Confirm how the chosen rinsing arrangement fits the approved water and hygiene process. A mineral-water label does not establish a different cap or bottle-handling geometry by itself.

  • Use controlled bottle and closure drawings rather than nominal volume or cap diameter alone.
  • Request change parts and achievable output for every launch format; review the PET compatibility guide.
  • Identify the actual rinsing, filling and capping machine and its offered filling principle, contact materials and test method.
  • Plan labeling, coding, packing and finished-pack removal on the same approved package, not an unrelated demonstration bottle.

Check Source Availability Against the Bottling Schedule

A 5,000 BPH run of 500ml bottles represents 2,500 liters per hour of nominal filled product. If a separate approved 1.5L format runs at 3,000 BPH, it represents 4,500 liters per hour. These are illustrative calculations, not offered machine rates. A larger bottle can increase water demand even when bottle throughput falls.

  • Add the actual requirements for rinsing, cleaning and other water consumers separately.
  • Review source availability, permitted operating schedule, treatment output and usable storage together.
  • A buffer may bridge a temporary mismatch, but it does not create additional daily water supply. Confirm storage design and operating conditions with the process specialist.
  • Use the mixed-format capacity guide before fixing a nominal line size.

Separate Equipment Acceptance From Water-Quality Release

A machine can reach the agreed bottle rate without demonstrating that every product requirement has been met. Build two connected acceptance records. The supplier and buyer should agree their own responsibilities and qualified testing arrangements before startup.

Separate Equipment Acceptance From Water-Quality Release - Planning Table

Acceptance track Examples to agree What it does not prove by itself
Mechanical package performance Format handling, fill check, closure, label, code, pack and sustained output. A satisfactory run does not establish finished-water composition or microbiological compliance.
Process and product release Approved water requirements, representative sampling and responsible release authority. An acceptable sample does not prove conveyor capacity or changeover performance.
Installed integration Actual water supply, utility connections, cleaning coverage and operating procedures. A factory trial does not automatically validate the final site installation.

Prepare a Mineral Water Filling Line Quotation

Send source information available, the intended water product, destination, bottle and cap drawings, good bottles per shift, label and pack, and treatment already installed. Mark unknown water-process inputs for specialist review. Request the mineral-water line configuration; compare the cost boundary and equipment schedule before comparing totals.

Background on Water Composition and Process Design

Buyer questions

Questions Buyers Ask Before Quotation

Does a mineral water filling machine add minerals?

The filler packages water supplied to its inlet; it does not define the mineral composition. Any composition adjustment belongs to a separately specified upstream process and must fit the approved product requirements.

Does every mineral water filling line need reverse osmosis?

No universal treatment package should be assumed. Select the process from source analysis, the intended composition and the requirements applying to the product and destination. Confirm those decisions with the responsible specialist before quoting the treatment scope.

Can the same line fill mineral water and purified water?

Potentially, if bottle, closure, product-contact materials and operating conditions are compatible. Review water transfer, cleaning, product segregation and release procedures separately. Mechanical compatibility does not approve a product change.

Can this still-water filling line also fill sparkling mineral water?

Do not assume so. Carbonation changes the process and filling conditions and can affect the package. Request a separate review of the carbonated duty rather than applying the still-water specification unchanged.

How much product water does 5000BPH of 500ml bottles use?

The nominal filled product is 2,500 liters per hour, calculated as 5,000 multiplied by 0.5 liters. This excludes rinsing, cleaning, treatment losses and other users, which must be included separately in the site water balance.

What evidence should I request before accepting a mineral water line?

Request the agreed mechanical and output test records plus the site process and water-quality release records assigned to the responsible parties. An operating video or bottle-rate display alone cannot establish all of those conditions.

Discuss Your Mineral Water and PET Bottle Requirements

Send your bottle size, target capacity and country with the source information and treatment scope available. Ask for a quotation that separates water-process responsibility from filling and packaging equipment.

Request Quote
WA: +86 186 6213 1120 Quote