Bottled water line solution guide
PET Water Bottle Base Deformation After Shrink Packing
Compare identified bottles before and after packing to establish where the shape changes. Examine the package, support and approved tunnel conditions together. A bottle that stands correctly before the tunnel but rocks afterward requires a different investigation from a bottle already deformed at filling.
Direct answer
Why do water bottles become unstable after the shrink tunnel?
Compare identified bottles before and after packing to establish where the shape changes. Examine the package, support and approved tunnel conditions together. A bottle that stands correctly before the tunnel but rocks afterward requires a different investigation from a bottle already deformed at filling.
- Baseline
- Inspect bottles before heat exposure.
- Support
- Compare bundle pattern and tunnel support.
- Exposure
- Retain speed and approved setting records.
- Cooling
- Inspect stability after an agreed cooling period.
Locate the first change in base shape
Take traceable samples at filler discharge, packer entry and tunnel exit, then recheck after the agreed cooling period. Record bottle lot, fill condition, pack pattern and any change to film or line speed. Do not attribute every unstable bottle to tunnel temperature; its base design, prior damage, support and package compression also need review.
Compare conditions without changing everything
Bottle-base investigation
| Pattern | Evidence | Next check |
|---|---|---|
| Deformed before packing | Upstream samples and lot identity | Bottle formation and prior handling |
| Only after tunnel | Exposure and before/after base profile | Approved heat and support conditions |
| Only outer bundle positions | Position map and pack pattern | Uneven exposure or compression |
| Stable initially, unstable later | Cooling and storage timeline | Package loading and retained samples |
Protect both bottle and bundle quality
- Ask qualified personnel to vary one approved condition at a time and retain matched samples. Keep the tunnel's safety controls active.
- Verify film integrity, bundle handling and bottle stability together; a cooler setting that produces loose packs is not an accepted solution.
- Use the actual bottle and film suppliers' limits. This guide specifies no universal tunnel temperature, belt speed or permissible base distortion.
Keep bottle, pack and tunnel evidence separate when bases distort
A distorted base at the end of shrink packing does not identify a temperature setting that should be changed. Start by determining the first point at which the package differs from its approved condition and whether the observation concerns the bottle, the bundle or both. Ask the bottle and packing specialists to review the actual configuration. This evidence plan gives no universal tunnel temperature, belt speed, cooling period or acceptable deformation limit, and it does not authorize access to hot moving equipment.
- Create an identified before-and-after comparison. Record bottle and closure references, lot, filled condition, film and pack pattern, plus the relevant trial interval. Preserve safe observations at packer entry, tunnel exit and the agreed later inspection point. A bottle sampled from a different lot or a pack opened much later may be useful evidence but is not an equivalent starting condition. State where identity or timing is uncertain.
- Separate the visible defects rather than writing heat problem for all of them. Describe base stability, local distortion, bottle lean, bundle restraint and the way the pack rests on the approved support. Note whether neighboring bottles or only certain positions are affected. The same final instability could involve an upstream bottle condition, support or formation issue as well as thermal exposure. Do not assign responsibility to the tunnel from the discovery location alone.
- Review the installed pack arrangement and the approved machine operating basis with qualified specialists. Identify relevant support, airflow and transfer conditions using supplier documentation and authorized observations. Compare recorded conditions, not just one displayed setpoint. A lower displayed temperature does not independently establish lower package exposure or acceptable film formation. Keep any proposed change within approved equipment and material instructions rather than applying settings copied from another bottle line.
- Agree a representative package trial and the observations needed at discharge and later handling. Include pack integrity, bottle stability and the intended downstream task, not merely whether the film looks tight. Change one approved condition at a time where feasible and record any necessary combined change as such. Keep safeguards active; sampling, isolated access and work near hot surfaces need the site's approved methods and qualified personnel.
- Close the packaging revision as a system. State which bottle, film, pattern, support and operating conditions were demonstrated, what remains unverified and who approves the package for its next handling stage. Do not automatically release earlier affected stock because a later trial looks better. A heavier bottle, extra cooling or different tunnel setting is a candidate action until the agreed evidence supports it; none is a universal remedy for every distorted base.
Quote packing against the actual bottle
Send Allot Tech bottle drawings and filled samples, film specification, bundle pattern, target packs per minute and defect records. Request a representative tunnel trial, defined inspection timing and handling criteria. Keep responsibility for bottle thermal suitability, packer settings and finished-pack approval explicit.
Planning sources and verification boundary
FAQ
Questions Buyers Ask Before Quotation
Should I simply reduce shrink-tunnel temperature?
First verify where deformation starts and follow the supplier's trial procedure. Evaluate bottle stability and bundle integrity together.
Can heavier bottles always solve the problem?
No. Base geometry, material distribution, prior condition and packing exposure matter; qualify the selected bottle rather than prescribing a weight.
When should the finished bottle be inspected?
Agree sampling points and cooling/storage conditions so before-and-after comparisons are repeatable.
Can I lower the tunnel setpoint and call the bottle-base problem solved?
Not from the setpoint alone. Compare identified packages before and after packing, review the actual approved conditions and verify both bottle stability and pack integrity. Qualified specialists should define the permitted change and the checks; this page does not supply a universal shrink-tunnel setting.
Request a Project-Specific Filling Line Review
Send your bottle size, target capacity, country, label and packing method. Allot Tech will prepare a bottled water filling line configuration and quotation boundary for review.